＃1

Meterer 2017-12-27 16:04编辑

大家好你们好，

在使用新的Cetus Mkii之后几天，我终于设法找到了SLIC3R的一些有用的设置。

棘手的部分：

当我开始找到正确的设置时，我第一次遇到我编写的每个G代码试图将X轴超出限制的问题。在删除额外的“G28”（归位命令）之后一切都效果正常。额外的归位似乎不需要，因为在初始化之后必须初始化打印机。

我的Z-Offset在印刷床上0.2mm。To ensure that the nozzle won’t crash the bed I manually wrote some g-code to move the nozzle to all 4 corners and approach the bed slowly to 0.5mm, then I measured the gap between the nozzle and the bed with a feeler gauge. To read the actual value I used the calibration function in the cetus-program.

我用350％的厚度印刷筏的第一层，以缩小喷嘴和床之间的间隙。这背后的初步想法是甚至略微不均匀的床。

我的设置远非理想的，只是将这个惊人的小型打印机充分潜力使用的第一步：眨眼：

这里 （https://imgur.com/gallery/96Kee）您可以在使用SLIC3R中使用Cetus Slicer和G代码与我的设置相比，在SLIC3R中进行比较。

问候，

m

config.zip.

＃2

你好，


谢谢你提供的详情。基本问题，你如何获得文件生成的文件SLIC3R到打印机？

＃3

在SLIC3R中，导出G代码（从“Plorater”选项卡），并且在Cetus3d中，您只需添加生成的文件。只需将其添加为.stl文件即可。

＃4

嗨，谢谢你分享这个。它适用于我，但我必须将挤出宽度的设置从200％到120％更改为挤出宽度。

SLIC3R手册

＃5

＃6

谢谢你的Slicer信息。这台机器不通过WiFi模拟Octoplint，所以如果我想通过网运行SLIC3R，我将必须使用PI前端它？

＃7

如果有人有兴趣。这是我的最终配置：

＃由SLIC3R 1.2.9在Sun 5月6日21:52:40 2018 Euthe_Crossing_Perimeters = 0 Bed_Shape = -180x0,0x0,0x180，-180x180 bed_temperature = 0 prefir_layer_gcode = loot_solid_layers = 8 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed =60 brim_width = 10 close_objects = 1冷却= 1 default_acceleration = 0 disable_fan_first_layers = 3 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = m109;关闭挤出机\ ng0 z-2; \ ng0 x-178 y2; \ nm2;程序结束external_fill_pattern =直线external_perimeter_extrusion_width = 0 external_perimeter_speed = 50％external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset =为0x0 extrusion_axis = E extrusion_multiplier = 24 extrusion_width = 0.48 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75fill_angle = 45 fill_density = 15％fill_pattern =蜂窝first_layer_acceleration = 0 first_layer_bed_temperature = 0 first_layer_extrusion_width = 0 first_layer_height = 0.2 first_layer_speed = 15 first_layer_temperature = 230 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor =的RepRap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width= 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15％infill_speed = 60 interface_shells = 0 layer_gcode = layer_height = 0.2 max_fan_speed = 100 max_print_speed = 80max_volumetric_speed = 0 min_fan_speed = 35 min_print_speed = 10 min_skirt_length = 0注释= nozzle_diameter = 0.4 octoprint_apikey = octoprint_host = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base] .gcode突出= 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 35个周边= 4 post_process = fuccess_adocance = 0 rast_layers = 0分辨率= 0 Retract_Before_Change = 0 Retract_Length = 10 Retract_Length_Lengt_Length_ToolChange = 10 Retract_lift = 0 Retract_restart_Extra = 0 Retract_restart_extra_ToolChange = 0 Retract_speed = 40 Seam_position =对齐Skirt_Distance = 20 Skirt_Height = 1脚步= 1慢速_Below_Layer_time= 5 small_perimeter_speed = 15 solid_infille_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = m204 P1500;设置加速\ ng1 z-2; \ ng0 x-90 y90; support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 4 support_material_speed = 60 support_material_threshold = 0 temperature = 230 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 8 travel_speed = 130 use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = 0 z_offset = -179.6
＃8

我无法下载config.zip文件，Sechel链接已损坏。它捕获此消息“oops！该页面不存在或私有。”

＃9

config.zip.（2.1 KB）
在这里，您有我的配置。别忘了调整z偏移！：眨眼：

1就像